Master Painter Interior Alkyd Calcimine Recoater

A professional interior oil base wall finish for use on all interior walls and ceilings including drywall, plaster, masonry, and primed wood. The rich, flat finish reduces the appearance of physical surface imperfections. Ideally suited for textured walls and ceilings. The oil base formula provides stain blocking characteristics on ceilings with minor smoke or water discoloration. Use a stain blocking primer where more severe stain discoloration is present. Ideally suited for commercial work where formal industry quality approvals are required. Approved by the Master Painter's Institute under category # 49.

PRICE $65.89

description

Name:Master Painter Interior Alkyd Calcimine Recoater
Category:Interior Paint
Classification:For Professionals
Chemistry:Alkyd
Sheen:GL1 "Flat" or "Matte"
Size/Liters:01 05 14
Product ID:86
Product Code:13163

Product Features:
• Ideal suited for textured walls and ceilings
• Stain blocking characteristics on ceilings with minor smoke or water discoloration
• Low light reflectance to mask surface defects
Product Description Marketing:
A professional interior oil base wall finish for use on all interior walls and ceilings including drywall, plaster, masonry, and primed wood. The rich, flat finish reduces the appearance of physical surface imperfections. Ideally suited for textured walls and ceilings. The oil base formula provides stain blocking characteristics on ceilings with minor smoke or water discoloration. Use a stain blocking primer where more severe stain discoloration is present. Ideally suited for commercial work where formal industry quality approvals are required. Approved by the Master Painter's Institute under category # 49.

application

Best paint for:

• Walls & ceilings
• Drywall, plaster
• Masonry, primed wood
Surface preparation:
Surface preparation is important. All surfaces must be smooth, clean, dry, free of mildew, grease, soap film, sanding dust or other contaminants. Remove all loose or peeling material from previously-painted surfaces. Wash all surfaces with a solution of 3 tablespoons of (Phosphate-free) TSP in a gallon of warm water. Rinse thoroughly, allow to dry and then scuff sand using 80-120 grit sandpaper on a hand sander. Remove all sanding dust. Do not apply at temperatures below 10˚C (50˚F).

WARNING! If you scrape, sand or remove old lead paint from any surface you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPAvacuum. For additional information, Canadian customers contact the Product Safety division of Health Canada at 1-800-O-CANADA, US customers contact the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323).
Recommended Primers:
Pre-Painted Surfaces: Self-Priming on properly-prepared pre-painted surfaces. Wash with a solution of 3 tablespoons of (Phosphate-free) TSP in a gallon of warm water. Rinse thoroughly, allow to dry, and then scuff sand using 80 to 120 grit sandpaper on a hand sander. Remove all sanding dust.

New or Bare Wood: Use Cloverdale Exterior Alkyd (15130) or Acrylic (05130).

Masonry: Self-priming or Cloverdale Latex Block Filler (05700).

Drywall: Cloverdale Hi-Hide Latex Drywall Sealer (05250).

Ferrous Metals (Steel, Iron): Use a suitable anti-corrosive primer such as Cloverdale 703-Series water-based or 710-Series Solvent-based Rustex primer.
Recommended Substrate:
Prepainted Drywall / Gypsum Pre-Painted Surfaces Concrete / Masonry Brick Ferrous Metals Particle Board New Wood Weathered Wood