VISIT MAIN SITE
My Account
Toggle Nav
Multimaster® Int/Exterior 100% Acrylic Latex Topcoat
Multimaster is Water-borne DTM Acrylic Urethane designed for both interior and exterior applications. Formulated with our VST (Variable Substrate Technology), this universal coating provides both functionality and aesthetic value in a low odor, non-flammable formulation. This quick dry product can be applied by brush, roll or spray with excellent flow and leveling. This hard wearing, non-blocking product it can be used for both commercial and DIY applications and complies with Government of Canada Emission regulations under category 52.
$98.89
- Multimaster® Int/Exterior 100% Acrylic Latex Topcoat
- Exterior Paint
- High Performance Interior Paint
- 100% Acrylic Latex
- GL5 "Semi-Gloss"
- 01 05 14
- 744
- 71423
-
Product Features:
• DTM and Self-priming to most surfaces
• Non-blocking
• Quick dry
• Contains VST Technology
• Water clean-up
• Excellent adhesion
• Interior / Exterior -
Product Description Marketing:
Multimaster is Water-borne DTM Acrylic Urethane designed for both interior and exterior applications. Formulated with our VST (Variable Substrate Technology), this universal coating provides both functionality and aesthetic value in a low odor, non-flammable formulation. This quick dry product can be applied by brush, roll or spray with excellent flow and leveling. This hard wearing, non-blocking product it can be used for both commercial and DIY applications and complies with Government of Canada Emission regulations under category 52.
-
Best paint for:
• Direct to metal
• Int/ext wood
• Concrete, plastics -
Surface preparation:
Surface preparation is important. All surfaces must be smooth, clean, dry, free of mildew, grease, soap film, sanding dust or other contaminants. Remove all loose or peeling material from previously-painted surfaces. Wash all surfaces with a solution of 3 tablespoons of (Phosphate-free) TSP in a gallon of warm water. Rinse thoroughly, allow to dry and then scuff sand using 80-120 grit sandpaper on a hand sander. Remove all sanding dust. Do not apply at temperatures below 10˚C (50˚F).
WARNING! If you scrape, sand or remove old lead paint from any surface you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPAvacuum. For additional information, Canadian customers contact the Product Safety division of Health Canada at 1-800-O-CANADA, US customers contact the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323).
Special Note: This product contains a sufficient level of an Environment Canada approved mildewcide to prevent mold, mildew and algae from growing on the surface of the coating. As mildew growth is, to a large degree dependent on a surface preparation and local conditions, Cloverdale Paint cannot guarantee that mildew will not grow through or on any contaminants which may have deposited on the surface of the coating.
-
Recommended Primers:
Pre-Painted Surfaces: Self-Priming on properly-prepared pre-painted surfaces.
New or Bare Wood: Use Cloverdale Exterior Alkyd (15130) or Acrylic (05130).
Masonry: Self-priming or Cloverdale Latex Block Filler (05700).
Drywall: Cloverdale Hi-Hide Latex Drywall Sealer (05250).
Ferrous Metals (Steel, Iron): Self-prime or Cloverdale 703-Series water-based or 710-Series Solvent-based Rustex primer.
Non-Ferrous: Self-prime or Cloverdale 703-Series water-based primer.
-
Recommended Substrate:
Aluminum Brick Composite Siding Composite Wood Concrete / Masonry Concrete Floors Concrete Masonry Units Ferrous Metals Fibreglass Glass Interior Concrete Floors New Drywall / Gypsum New Wood Non-Ferrous Metals Particle Board Plastic Prepainted Drywall /
